MULTIPARAMETER WATER QUALITY METER (PH / ISE / EC / DO / TURBIDITY)
$USD 3,388.00
HI9829C10T
Surpasses the precision of alternative water sampling systems
The HI9829 is a multiparameter water quality meter that monitors up to 14 different water quality parameters.
The microprocessor-based multi-sensor probe allows for the measurement of key parameters including pH, ORP, conductivity, dissolved oxygen, turbidity, ammonium, chloride, nitrate, and temperature. The probe transmits readings digitally with options to log data while disconnected from the meter. An optional GPS provides location tracking of measurements. Besides, the complete system is simple to set up and easy to use. This multiparameter water meter is highly customizable and supplied with all necessary accessories, packaged in a durable carrying case.
- Optional GPS provides location tracking of measurements.
- Color-coded, field-replaceable sensors
- Great for environmental, field, and laboratory testing.
Built-in GPS Receiver
- 12-channel GPS receiver and antenna
- Tracks location using satellites to within 30 feet
- Latitude and longitude recorded with readings
- Location naming for GPS coordinates
- Distance from the current location to the stored location
- Hi929829 multiparameter water quality meter software supplied integrates data collected with Google™ maps - Measurement readings including GPS coordinates - Date and time - Named locations and remarks - Sample number
HI9829-MULTIPARAMETER WATER QUALITY METER | PH / ISE / EC / DO / TURBIDITY
Two probes to choose from (Basic or Logging)
The HI7609829 (basic) and HI7629829 (logging) are multiparameter water meter probes for use with the HI9829 portable meter. It is an option to choose which probe will be supplied with the HI9829 multiparameter water quality meter. By default, the HI9829 and corresponding probe will be supplied with pH/ORP, conductivity, and dissolved oxygen sensors. Therefore, either probe can be upgraded to measure turbidity with a turbidity/conductivity sensor.
HI7609829 Basic Probe
- Digital probe that is less than 2 inches in diameter
- 3 color-coded sensor inputs
- IP68 rating for continuous immersion in water
- Multistrand –multiconductor cable rated for 150 lbs (intermittent use)
- Available with 4, 10, or 20-meter cable
- A weighted shield protects all sensors
HI7609829 probe without logging
- HI7629829 Autonomously Logging Probe
- Same as basic probe but with logging capability
- Logs data independent of HI9829 meter
- Operates on 4 “AA” batteries for up to 70 days*
- Stores up to 140,000 single parameter readings or 35,000 for all parameters
- Logs data from 1 second to 3 hours
- Choose to be supplied with EC or EC/Turbidity sensor
- Supplied with a USB cable for direct connection to Window’s compatible PC
*All channels logging at 10-minute intervals with no averaging
Color-Coded, Field Replaceable Sensors
Waterproof Protection
The multiparameter water quality meter is enclosed in an IP67 rated waterproof casing and can withstand immersion in water at a depth of 1 m for up to 30 minutes. The probe features an IP68 rating for continuous immersion in water.Backlit Dot Matrix LCD Display
[caption id="attachment_22942" align="alignnone" width="238"]
display[/caption]
The HI9829 features a backlit graphic LCD with on-screen help and the capability to display up to twelve parameters simultaneously. The graphic display allows for the use of virtual keys to provide for an intuitive user interface.
Intuitive Keypad
The fitted rubber keypad has dedicated keys for power, backlight, up/down arrows, help, and alphanumeric characters. The meter also features two virtual soft keys that navigate the user through the configuration of each parameter, meter setup and logging of data. The interface is intuitive for any user’s level of experience.Dedicated Help Key
Contextual help is always available through a dedicated “HELP” key. Clear tutorial messages and directions are available on-screen to quickly and easily guide users through setup and calibration. The help information displayed is relative to the setting/option being viewed.Auto-sensor Recognition
The probe and meter automatically recognize the sensors that are connected. Any ports not used on the probe will not have the parameter displayed or be configurable.Automatic temperature compensation
The integrated temperature sensor allows for automatic temperature compensation of pH, conductivity, and dissolved oxygen measurements.Automatic Barometric Pressure Compensation
The meter features a built-in barometer with user-selectable units for dissolved oxygen pressure compensation.Quick Calibration
Quick Calibration provides a speedy, single-point calibration for pH, conductivity, and dissolved oxygen. Standard calibration options are available including pH up to three points, Conductivity at one point, and dissolved oxygen up to two points.
GLP Data
HI9829 includes a GLP feature that allows users to view calibration data and calibration expiration information at the touch of a key. Calibration data includes the date, time, buffers/standards used for calibration, and slope characteristics.Data Logging
The HI9829 allows users to store up to 44,000 continuous or log-on-demand samples with logging intervals from one second to three hours.Graphing Capability
Trend graphing with sample date and time stamp may be viewed on the display or transferred to a pc.
PC Connectivity
Logged data can be transferred to a Windows-compatible PC with the included HI7698291 USB adapter and HI929829 software.Long Battery Life
The display of the meter has a battery icon indicator to show the remaining power. The meter is supplied with four 1.5V “C “ NiMH rechargeable batteries that provide up to 140 hours of battery life*Rugged thermoformed carrying case
The HI9829 meter, probe, and all accessories are supplied in a rugged carrying case designed to provide years of use. The inside compartment of the carrying case is thermoformed to securely hold and protect all of the components.
* Without GPS or turbidity measurements
GPS Option
The meter features an internal 12 channel GPS receiver and antenna that calculates its position to track locations along with measurement data.Fast Tracker™—Tag Identification System
HANNA’s Fact Tracker™—Tag Identification System simplifies test logging. iButtons with a unique ID can be installed at various sampling sites. When the matching connector on the meter contacts the location button, measurements are logged and labeled with the alphanumeric user-entered location ID. Location, date, time and measurements are logged into the meter which can be transferred to a PC. The Fast Tracker™ system complements the GPS for ultimate tracking.iButton. Tags are Easy to Install
Install the optional TAGs near your sampling points for quick and easy iButton readings. Each TAG contains a computer chip with a unique identification code encased in stainless steel. You can install a practically unlimited amount of TAGs. Additional TAGs can be ordered for all of your traceability requirements. Hanna HI9829 how to use INITIALIZATION AND MEASUREMENT HI9829 is supplied with 4 rechargeable, size C NiMH (Nickel-metal hydride) batteries. The battery symbol on the LCD indicates the remaining battery charge. The meter has a low battery warning, and when the symbol starts blinking, batteries should be charged or replaced with new ones. When the batteries are discharged the meter will automatically shut off to avoid erroneous readings. Meter Battery Installation Replace batteries in safe areas only. Remove the 4 screws on the rear of the instrument and insert the batteries observing polarity. If you wish to replace the supplied rechargeable batteries with non-rechargeable alkaline batteries, move the switch in the battery compartment upward. A warning message is displayed if you connect the charging cable to a meter with alkaline batteries. Non-rechargeable alkaline batteries can explode or leak if you try to charge them. Verify that the switch is in the up position when using alkaline batteries to prevent recharging. Note: Do not mix old and new alkaline batteries. Learn more in the Instruction Manual / Quick Start Guide| pH Range | 0.00 to 14.00 pH |
|---|---|
| pH Resolution | 0.01 pH |
| pH Accuracy | ±0.02 pH |
| pH Calibration | automatic one, two, or three points with automatic recognition of five standard buffers (pH 4.01, 6.86, 7.01, 9.18, 10.01) or one custom buffer |
| mV Range | ±600.0 mV |
| mV Resolution | 0.1 mV |
| mV Accuracy | ±0.5 mV |
| ORP Range | ±2000 mV |
| ORP Resolution | 0.1 mV |
| ORP Accuracy | ±1.0 mV |
| ORP Calibration | automatic at one custom point (relative mV) |
| EC Range | 0 to 200 mS/cm (absolute EC up to 400 mS/cm) |
| EC Resolution | Manual: 1 µS/cm; 0.001 mS/cm; 0.01 mS/cm; 0.1 mS/cm; 1 mS/cm, Automatic: 1 µS/cm from 0 to 9999 µS/cm; 0.01 mS/cm from 10.00 to 99.99 mS/cm; 0.1 mS/cm from 100.0 to 400.0 mS/cm, Automatic (mS/cm): 0.001 mS/cm from 0.000 to 9.999 mS/cm; 0.01 mS/cm from 10.00 to 99.99 mS/cm; 0.1 mS/cm from 100.0 to 400.0 mS/cm |
| EC Accuracy | ±1% of reading or ±1 µS/cm whichever is greater |
| EC Calibration | automatic single point, with six standard solutions (84 µS/cm, 1413 µS/cm, 5.00 mS/cm, 12.88 mS/cm, 80.0 mS/cm, 111.8 mS/cm) or custom point |
| TDS Range | 0 to 400000 ppm (mg/L); (the maximum value depends on the TDS factor) |
| TDS Resolution | Manual: 1 ppm (mg/L); 0.001 ppt (g/L); 0.01 ppt (g/L); 0.1 ppt (g/L); 1 ppt (g/L),Automatic: 1 ppm (mg/L) from 0 to 9999 ppm (mg/L); 0.01 ppt (g/L) from 10.00 to 99.99 ppt (g/L); 0.1 ppt (g/L) from 100.0 to 400.0 ppt (g/L),Automatic ppt (g/L): 0.001 ppt (g/L) from 0.000 to 9.999 ppt (g/L); 0.01 ppt (g/L) from 10.00 to 99.99 ppt (g/L); 0.1 ppt (g/L) from 100.0 to 400.0 ppt (g/L) |
| TDS Accuracy | ±1% of reading or ±1 ppm (mg/L), whichever is greater |
| TDS Calibration | based on conductivity or salinity calibration |
| Resistivity Range | 0 to 999999 Ω•cm; 0 to 1000.0 kΩ•cm; 0 to 1.0000 MΩ•cm |
| Resistivity Resolution | dependent on resistivity reading |
| Resistivity Calibration | based on conductivity calibration |
| Salinity Range | 0.00 to 70.00 PSU |
| Salinity Resolution | 0.01 PSU |
| Salinity Accuracy | ±2% of reading or ±0.01 PSU whichever is greater |
| Salinity Calibration | based on conductivity calibration |
| Seawater σ Range | 0.0 to 50.0 σt, σ₀, σ₁₅ |
| Seawater σ Resolution | 0.1 σt, σ₀, σ₁₅ |
| Seawater σ Accuracy | ±1 σt, σ₀, σ₁₅ |
| Seawater σ Calibration | based on conductivity or salinity calibration |
| Ammonium-Nitrogen Range | 0.02 to 200.0 ppm Am (as NH4 +-N) |
| Ammonium-Nitrogen Resolution | 0.01 ppm to 1 ppm 0.1 ppm to 200.0 ppm |
| Ammonium-Nitrogen Accuracy | ±5 % reading or 2 ppm |
| Ammonium-Nitrogen Calibration | 1 or 2 point, 10 ppm and 100 ppm |
| Chloride Range | 0.6 to 200.0 ppm Cl (as Cl- ) |
| Chloride Resolution | 0.01 ppm to 1 ppm 0.1 ppm to 200.0 ppm |
| Chloride Accuracy | ±5 % of reading or 2 ppm |
| Chloride Calibration | 1 or 2 point, 10 ppm and 100 ppm |
| Nitrate-Nitrogen Range | 0.62 to 200.0 ppm Ni (as NO3 - -N) |
| Nitrate-Nitrogen Resolution | 0.01 ppm to 1 ppm 0.1 ppm to 200 ppm |
| Nitrate-Nitrogen Accuracy | ±5 % of reading or 2 ppm |
| Nitrate-Nitrogen Calibration | 1 or 2 point, 10 ppm and 100 ppm |
| Turbidity Range | 0.0 to 99.9 FNU; 100 to 1000 FNU |
| Turbidity Resolution | 0.1 FNU from 0.0 to 99.9 FNU 1 FNU from 100 to 1000 FNU |
| Turbidity Accuracy | ±0.3 FNU or ±2 % of reading, whichever is greater |
| Turbidity Calibration | Automatic 1, 2, or, 3 points at 0, 20 and 200 FNU, or custom |
| DO Range | 0.0 to 500.0%; 0.00 to 50.00 ppm (mg/L) |
| DO Resolution | 0.1%; 0.01 ppm (mg/L) |
| DO Accuracy | 0.0 to 300.0% saturation: ±1.5% of reading or ±1.0% saturation whichever is greater, 0.00 to 30.00 ppm (mg/L): ±1.5% of reading or ±0.10 ppm (mg/L),whichever is greater, 30.00 ppm (mg/L) to 50.00 ppm (mg/L): ±3% of reading, 300.0 to 500.0% saturation: ±3% of reading |
| DO Calibration | automatic one or two points at 0 and 100% or one custom point |
| Atmospheric Pressure Range | 450 to 850 mm Hg; 17.72 to 33.46 in Hg; 600.0 to 1133.2 mbar; 8.702 to 16.436 psi; 0.5921 to 1.1184 atm; 60.00 to 113.32 kPa |
| Atmospheric Pressure Resolution | 0.1 mm Hg; 0.01 in Hg; 0.1 mbar; 0.001 psi; 0.0001 atm; 0.01 kPa |
| Atmospheric Pressure Accuracy | ±3 mm Hg within ±15°C from the temperature during calibration |
| Atmospheric Pressure Calibration | automatic at one custom point |
| Temperature Range | -5.00 to 55.00 °C, 23.00 to 131.00 °F, 268.15 to 328.15 K |
| Temperature Resolution | 0.01 K, 0.01 °C, 0.01 °F |
| Temperature Accuracy | ±0.15 °C; ±0.27 °F; ±0.15 K |
| Temperature Calibration | automatic at one custom point |
| Temperature Compensation | automatic from -5 to 55 °C (23 to 131 °F) |
| Logging Memory | 44,000 records (continuous logging or log-on-demand of all parameters) |
| Logging Interval | one second to three hours |
| PC Connectivity | USB (with HI 929829 software) |
| Battery Type/Life | 1.2V (4) NiMH, rechargeable batteries, size C type; up to 140 hours depending on configuration |
| Waterproof Protection | IP67 |
| Environment | 0 to 50°C (32 to 122°F); RH max 100% |
| Dimensions | 221 x 115 x 55 mm (8.7 x 4.5 x 2.2”) |
| Weight | 750 g (26.5 oz.) |
| GPS | 12 channel receiver 10 m (30 ft) accuracy |
| Price | $USD 3,388.00 |
|---|
Write Your Own Review
Need larger scale equipment for a bigger project?
Our parent site geneq.com works by quote requests, so we can offer a unique price per any combination of items you choose, and the best shipping company/route for weighty items. We distribute the biggest names in the industry since 1972!
Copyright © Geneq USA 2025
